| Common Name: | RARUS 427 |
| Manufacturer: | EXXON MOBIL |
| MSDS Revision Date: | 8/19/2011 |
| Grainger Item Number(s): | 4F978, 4ZF21, 5Z706, 5Z707 |
| Manufacturer Model Number(s): | 5Z706, 5Z707, RARUS 427 |
MSDS Table of Contents
Click the desired link below to jump directly to that section in the MSDS.
EXXONMOBIL
PRODUCT NAME: MOBIL RARUS 427
REVISION DATE: 19 AUG 2011
MATERIAL SAFETY DATA SHEET
| SECTION 1 PRODUCT AND COMPANY IDENTIFICATION |  |
PRODUCT:
PRODUCT NAME: MOBIL RARUS 427
PRODUCT DESCRIPTION: BASE OIL AND ADDITIVES
PRODUCT CODE: 606202-00, 970996
INTENDED USE: COMPRESSOR OIL
COMPANY IDENTIFICATION:
SUPPLIER:
EXXON MOBIL CORPORATION
3225 GALLOWS RD.
FAIRFAX, VA. 22037
USA
24 HOUR HEALTH EMERGENCY: 609-737-4411
TRANSPORTATION EMERGENCY PHONE: 800-424-9300
EXXONMOBIL TRANSPORTATION NO.: 281-834-3296
PRODUCT TECHNICAL INFORMATION:
800-662-4525
800-947-9147
MSDS INTERNET ADDRESS:
HTTP://WWW.EXXON.COM
HTTP://WWW.MOBIL.COM
| SECTION 2 COMPOSITION / INFORMATION ON INGREDIENTS | |
NO REPORTABLE HAZARDOUS SUBSTANCE(S) OR COMPLEX SUBSTANCE(S).:
| SECTION 3 HAZARDS IDENTIFICATION | |
THIS MATERIAL IS NOT CONSIDERED TO BE HAZARDOUS ACCORDING TO REGULATORY
GUIDELINES (SEE (M)SDS SECTION 15).
POTENTIAL HEALTH EFFECTS:
LOW ORDER OF TOXICITY. EXCESSIVE EXPOSURE MAY RESULT IN EYE, SKIN, OR
RESPIRATORY IRRITATION. HIGH-PRESSURE INJECTION UNDER SKIN MAY CAUSE SERIOUS
DAMAGE.
NFPA HAZARD ID:
HEALTH 0
FLAMMABILITY 1
REACTIVITY 0
HMIS HAZARD ID:
HEALTH 0
FLAMMABILITY 1
REACTIVITY 0
NOTE:
THIS MATERIAL SHOULD NOT BE USED FOR ANY OTHER PURPOSE THAN THE INTENDED USE
IN SECTION 1 WITHOUT EXPERT ADVICE. HEALTH STUDIES HAVE SHOWN THAT CHEMICAL
EXPOSURE MAY CAUSE POTENTIAL HUMAN HEALTH RISKS WHICH MAY VARY FROM PERSON
TO PERSON.
| SECTION 4 FIRST AID MEASURES | |
INHALATION:
REMOVE FROM FURTHER EXPOSURE. FOR THOSE PROVIDING ASSISTANCE, AVOID EXPOSURE
TO YOURSELF OR OTHERS. USE ADEQUATE RESPIRATORY PROTECTION. IF RESPIRATORY
IRRITATION, DIZZINESS, NAUSEA, OR UNCONSCIOUSNESS OCCURS, SEEK IMMEDIATE
MEDICAL ASSISTANCE. IF BREATHING HAS STOPPED, ASSIST VENTILATION WITH A
MECHANICAL DEVICE OR USE MOUTH-TO-MOUTH RESUSCITATION.
SKIN CONTACT:
WASH CONTACT AREAS WITH SOAP AND WATER. IF PRODUCT IS INJECTED INTO OR UNDER
THE SKIN, OR INTO ANY PART OF THE BODY, REGARDLESS OF THE APPEARANCE OF THE
WOUND OR ITS SIZE, THE INDIVIDUAL SHOULD BE EVALUATED IMMEDIATELY BY A
PHYSICIAN AS A SURGICAL EMERGENCY. EVEN THOUGH INITIAL SYMPTOMS FROM HIGH
PRESSURE INJECTION MAY BE MINIMAL OR ABSENT, EARLY SURGICAL TREATMENT WITHIN
THE FIRST FEW HOURS MAY SIGNIFICANTLY REDUCE THE ULTIMATE EXTENT OF INJURY.
EYE CONTACT:
FLUSH THOROUGHLY WITH WATER. IF IRRITATION OCCURS, GET MEDICAL ASSISTANCE.
INGESTION:
FIRST AID IS NORMALLY NOT REQUIRED. SEEK MEDICAL ATTENTION IF DISCOMFORT
OCCURS.
| SECTION 5 FIRE FIGHTING MEASURES | |
EXTINGUISHING MEDIA:
APPROPRIATE EXTINGUISHING MEDIA:
USE WATER FOG, FOAM, DRY CHEMICAL OR CARBON DIOXIDE (CO2) TO EXTINGUISH
FLAMES.
INAPPROPRIATE EXTINGUISHING MEDIA: STRAIGHT STREAMS OF WATER
FIRE FIGHTING:
FIRE FIGHTING INSTRUCTIONS:
EVACUATE AREA. PREVENT RUNOFF FROM FIRE CONTROL OR DILUTION FROM ENTERING
STREAMS, SEWERS, OR DRINKING WATER SUPPLY. FIREFIGHTERS SHOULD USE STANDARD
PROTECTIVE EQUIPMENT AND IN ENCLOSED SPACES, SELF-CONTAINED BREATHING
APPARATUS (SCBA). USE WATER SPRAY TO COOL FIRE EXPOSED SURFACES AND TO
PROTECT PERSONNEL.
HAZARDOUS COMBUSTION PRODUCTS:
SMOKE, FUME, ALDEHYDES, SULFUR OXIDES, INCOMPLETE COMBUSTION PRODUCTS,
OXIDES OF CARBON
FLAMMABILITY PROPERTIES:
FLASH POINT [METHOD]: >210C (410F) [ASTM D-92]
FLAMMABLE LIMITS (APPROXIMATE VOLUME % IN AIR):
LEL: 0.9
UEL: 7.0
AUTOIGNITION TEMPERATURE: N/D
| SECTION 6 ACCIDENTAL RELEASE MEASURES | |
NOTIFICATION PROCEDURES:
IN THE EVENT OF A SPILL OR ACCIDENTAL RELEASE, NOTIFY RELEVANT AUTHORITIES
IN ACCORDANCE WITH ALL APPLICABLE REGULATIONS. US REGULATIONS REQUIRE
REPORTING RELEASES OF THIS MATERIAL TO THE ENVIRONMENT WHICH EXCEED THE
APPLICABLE REPORTABLE QUANTITY OR OIL SPILLS WHICH COULD REACH ANY WATERWAY
INCLUDING INTERMITTENT DRY CREEKS. THE NATIONAL RESPONSE CENTER CAN BE
REACHED AT (800)424-8802.
PROTECTIVE MEASURES:
AVOID CONTACT WITH SPILLED MATERIAL. SEE SECTION 5 FOR FIRE FIGHTING
INFORMATION. SEE THE HAZARD IDENTIFICATION SECTION FOR SIGNIFICANT HAZARDS.
SEE SECTION 4 FOR FIRST AID ADVICE. SEE SECTION 8 FOR ADVICE ON THE MINIMUM
REQUIREMENTS FOR PERSONAL PROTECTIVE EQUIPMENT. ADDITIONAL PROTECTIVE
MEASURES MAY BE NECESSARY, DEPENDING ON THE SPECIFIC CIRCUMSTANCES AND/OR
THE EXPERT JUDGMENT OF THE EMERGENCY RESPONDERS.
FOR EMERGENCY RESPONDERS:
RESPIRATORY PROTECTION:
RESPIRATORY PROTECTION WILL BE NECESSARY ONLY IN SPECIAL CASES, E.G.,
FORMATION OF MISTS. HALF-FACE OR FULL-FACE RESPIRATOR WITH FILTER(S) FOR
DUST/ORGANIC VAPOR OR SELF CONTAINED BREATHING APPARATUS (SCBA) CAN BE USED
DEPENDING ON THE SIZE OF SPILL AND POTENTIAL LEVEL OF EXPOSURE. IF THE
EXPOSURE CANNOT BE COMPLETELY CHARACTERIZED OR AN OXYGEN DEFICIENT
ATMOSPHERE IS POSSIBLE OR ANTICIPATED, SCBA IS RECOMMENDED. WORK GLOVES THAT
ARE RESISTANT TO HYDROCARBONS ARE RECOMMENDED. GLOVES MADE OF POLYVINYL
ACETATE (PVA) ARE NOT WATER-RESISTANT AND ARE NOT SUITABLE FOR EMERGENCY
USE. CHEMICAL GOGGLES ARE RECOMMENDED IF SPLASHES OR CONTACT WITH EYES IS
POSSIBLE.
SMALL SPILLS:
NORMAL ANTISTATIC WORK CLOTHES ARE USUALLY ADEQUATE.
LARGE SPILLS:
FULL BODY SUIT OF CHEMICAL RESISTANT, ANTISTATIC MATERIAL IS RECOMMENDED.
SPILL MANAGEMENT:
LAND SPILL:
STOP LEAK IF YOU CAN DO IT WITHOUT RISK. RECOVER BY PUMPING OR WITH SUITABLE
ABSORBENT.
WATER SPILL:
STOP LEAK IF YOU CAN DO IT WITHOUT RISK. CONFINE THE SPILL IMMEDIATELY WITH
BOOMS. WARN OTHER SHIPPING. REMOVE FROM THE SURFACE BY SKIMMING OR WITH
SUITABLE ABSORBENTS. SEEK THE ADVICE OF A SPECIALIST BEFORE USING
DISPERSANTS.
WATER SPILL AND LAND SPILL RECOMMENDATIONS ARE BASED ON THE MOST LIKELY
SPILL SCENARIO FOR THIS MATERIAL; HOWEVER, GEOGRAPHIC CONDITIONS, WIND,
TEMPERATURE, (AND IN THE CASE OF A WATER SPILL) WAVE AND CURRENT DIRECTION
AND SPEED MAY GREATLY INFLUENCE THE APPROPRIATE ACTION TO BE TAKEN. FOR THIS
REASON, LOCAL EXPERTS SHOULD BE CONSULTED.
NOTE: LOCAL REGULATIONS MAY PRESCRIBE OR LIMIT ACTION TO BE TAKEN.
ENVIRONMENTAL PRECAUTIONS:
LARGE SPILLS:
DIKE FAR AHEAD OF LIQUID SPILL FOR LATER RECOVERY AND DISPOSAL. PREVENT
ENTRY INTO WATERWAYS, SEWERS, BASEMENTS OR CONFINED AREAS.
| SECTION 7 HANDLING AND STORAGE | |
HANDLING:
THIS MATERIAL IS NOT INTENDED FOR USE IN AIR COMPRESSORS FOR BREATHING
APPLICATIONS. PREVENT SMALL SPILLS AND LEAKAGE TO AVOID SLIP HAZARD.
MATERIAL CAN ACCUMULATE STATIC CHARGES WHICH MAY CAUSE AN ELECTRICAL SPARK
(IGNITION SOURCE). WHEN THE MATERIAL IS HANDLED IN BULK, AN ELECTRICAL SPARK
COULD IGNITE ANY FLAMMABLE VAPORS FROM LIQUIDS OR RESIDUES THAT MAY BE
PRESENT (E.G., DURING SWITCH-LOADING OPERATIONS). USE PROPER BONDING AND/OR
GROUND PROCEDURES. HOWEVER, BONDING AND GROUNDS MAY NOT ELIMINATE THE
HAZARD FROM STATIC ACCUMULATION. CONSULT LOCAL APPLICABLE STANDARDS FOR
GUIDANCE. ADDITIONAL REFERENCES INCLUDE AMERICAN PETROLEUM INSTITUTE 2003
(PROTECTION AGAINST IGNITIONS ARISING OUT OF STATIC, LIGHTNING AND STRAY
CURRENTS) OR NATIONAL FIRE PROTECTION AGENCY 77 (RECOMMENDED PRACTICE ON
STATIC ELECTRICITY) OR CENELEC CLC/TR 50404 (ELECTROSTATICS - CODE OF
PRACTICE FOR THE AVOIDANCE OF HAZARDS DUE TO STATIC ELECTRICITY).
STATIC ACCUMULATOR: THIS MATERIAL IS A STATIC ACCUMULATOR.
STORAGE:
THE CONTAINER CHOICE, FOR EXAMPLE STORAGE VESSEL, MAY EFFECT STATIC
ACCUMULATION AND DISSIPATION. DO NOT STORE IN OPEN OR UNLABELLED CONTAINERS.
KEEP AWAY FROM INCOMPATIBLE MATERIALS.
| SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION | |
EXPOSURE LIMITS/STANDARDS FOR MATERIALS THAT CAN BE FORMED WHEN HANDLING
THIS PRODUCT:
WHEN MISTS/AEROSOLS CAN OCCUR THE FOLLOWING ARE RECOMMENDED:
5 MG/M3 - ACGIH TLV (INHALABLE FRACTION), 5 MG/M3 - OSHA PEL.
NOTE:
LIMITS/STANDARDS SHOWN FOR GUIDANCE ONLY. FOLLOW APPLICABLE REGULATIONS.
ENGINEERING CONTROLS:
THE LEVEL OF PROTECTION AND TYPES OF CONTROLS NECESSARY WILL VARY DEPENDING
UPON POTENTIAL EXPOSURE CONDITIONS.
CONTROL MEASURES TO CONSIDER:
NO SPECIAL REQUIREMENTS UNDER ORDINARY CONDITIONS OF USE AND WITH ADEQUATE
VENTILATION.
PERSONAL PROTECTION:
PERSONAL PROTECTIVE EQUIPMENT SELECTIONS VARY BASED ON POTENTIAL EXPOSURE
CONDITIONS SUCH AS APPLICATIONS, HANDLING PRACTICES, CONCENTRATION AND
VENTILATION. INFORMATION ON THE SELECTION OF PROTECTIVE EQUIPMENT FOR USE
WITH THIS MATERIAL, AS PROVIDED BELOW, IS BASED UPON INTENDED, NORMAL USAGE.
RESPIRATORY PROTECTION:
IF ENGINEERING CONTROLS DO NOT MAINTAIN AIRBORNE CONTAMINANT CONCENTRATIONS
AT A LEVEL WHICH IS ADEQUATE TO PROTECT WORKER HEALTH, AN APPROVED
RESPIRATOR MAY BE APPROPRIATE. RESPIRATOR SELECTION, USE, AND MAINTENANCE
MUST BE IN ACCORDANCE WITH REGULATORY REQUIREMENTS, IF APPLICABLE.
TYPES OF RESPIRATORS TO BE CONSIDERED FOR THIS MATERIAL INCLUDE:
NO SPECIAL REQUIREMENTS UNDER ORDINARY CONDITIONS OF USE AND WITH ADEQUATE
VENTILATION.
FOR HIGH AIRBORNE CONCENTRATIONS, USE AN APPROVED SUPPLIED-AIR RESPIRATOR,
OPERATED IN POSITIVE PRESSURE MODE. SUPPLIED AIR RESPIRATORS WITH AN ESCAPE
BOTTLE MAY BE APPROPRIATE WHEN OXYGEN LEVELS ARE INADEQUATE, GAS/VAPOR
WARNING PROPERTIES ARE POOR, OR IF AIR PURIFYING FILTER CAPACITY/RATING MAY
BE EXCEEDED.
HAND PROTECTION:
ANY SPECIFIC GLOVE INFORMATION PROVIDED IS BASED ON PUBLISHED LITERATURE
AND GLOVE MANUFACTURER DATA. GLOVE SUITABILITY AND BREAKTHROUGH TIME WILL
DIFFER DEPENDING ON THE SPECIFIC USE CONDITIONS. CONTACT THE GLOVE
MANUFACTURER FOR SPECIFIC ADVICE ON GLOVE SELECTION AND BREAKTHROUGH TIMES
FOR YOUR USE CONDITIONS. INSPECT AND REPLACE WORN OR DAMAGED GLOVES.
THE TYPES OF GLOVES TO BE CONSIDERED FOR THIS MATERIAL INCLUDE:
NO PROTECTION IS ORDINARILY REQUIRED UNDER NORMAL CONDITIONS OF USE.
EYE PROTECTION:
IF CONTACT IS LIKELY, SAFETY GLASSES WITH SIDE SHIELDS ARE RECOMMENDED.
SKIN AND BODY PROTECTION:
ANY SPECIFIC CLOTHING INFORMATION PROVIDED IS BASED ON PUBLISHED LITERATURE
OR MANUFACTURER DATA.
THE TYPES OF CLOTHING TO BE CONSIDERED FOR THIS MATERIAL INCLUDE:
NO SKIN PROTECTION IS ORDINARILY REQUIRED UNDER NORMAL CONDITIONS OF USE.
IN ACCORDANCE WITH GOOD INDUSTRIAL HYGIENE PRACTICES, PRECAUTIONS SHOULD BE
TAKEN TO AVOID SKIN CONTACT.
SPECIFIC HYGIENE MEASURES:
ALWAYS OBSERVE GOOD PERSONAL HYGIENE MEASURES, SUCH AS WASHING AFTER
HANDLING THE MATERIAL AND BEFORE EATING, DRINKING, AND/OR SMOKING. ROUTINELY
WASH WORK CLOTHING AND PROTECTIVE EQUIPMENT TO REMOVE CONTAMINANTS. DISCARD
CONTAMINATED CLOTHING AND FOOTWEAR THAT CANNOT BE CLEANED. PRACTICE GOOD
HOUSEKEEPING.
ENVIRONMENTAL CONTROLS: SEE SECTIONS 6, 7, 12, 13.
| SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES | |
NOTE:
PHYSICAL AND CHEMICAL PROPERTIES ARE PROVIDED FOR SAFETY, HEALTH AND
ENVIRONMENTAL CONSIDERATIONS ONLY AND MAY NOT FULLY REPRESENT PRODUCT
SPECIFICATIONS. CONTACT THE SUPPLIER FOR ADDITIONAL INFORMATION.
GENERAL INFORMATION:
PHYSICAL STATE: LIQUID
COLOR: AMBER
ODOR: CHARACTERISTIC
ODOR THRESHOLD: N/D
IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION:
RELATIVE DENSITY (AT 15 C): 0.879
FLASH POINT [METHOD]: >210C (410F) [ASTM D-92]
FLAMMABLE LIMITS (APPROXIMATE VOLUME % IN AIR):
LEL: 0.9
UEL: 7.0
AUTOIGNITION TEMPERATURE: N/D
BOILING POINT / RANGE: >316C (600F)
VAPOR DENSITY (AIR =1): >2 AT 101 KPA
VAPOR PRESSURE: <0.013 KPA (0.1 MMHg) AT 20 C
EVAPORATION RATE (N-BUTYL ACETATE = 1): N/D
PH: N/A
LOG POW (N-OCTANOL/WATER PARTITION COEFFICIENT): >3.5
SOLUBILITY IN WATER: NEGLIGIBLE
VISCOSITY: 100 CST (100 MM2/SEC) AT 40 C
OXIDIZING PROPERTIES: SEE HAZARDS IDENTIFICATION SECTION.
OTHER INFORMATION:
FREEZING POINT: N/D
MELTING POINT: N/A
POUR POINT: -9 DEG. C (16 DEG. F)
DMSO EXTRACT (MINERAL OIL ONLY), IP-346: <3 %WT
| SECTION 10 STABILITY AND REACTIVITY | |
STABILITY: MATERIAL IS STABLE UNDER NORMAL CONDITIONS.
CONDITIONS TO AVOID: EXCESSIVE HEAT. HIGH ENERGY SOURCES OF IGNITION.
MATERIALS TO AVOID: STRONG OXIDIZERS
HAZARDOUS DECOMPOSITION PRODUCTS:
MATERIAL DOES NOT DECOMPOSE AT AMBIENT TEMPERATURES.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR.
| SECTION 11 TOXICOLOGICAL INFORMATION | |
ACUTE TOXICITY:
ROUTE OF EXPOSURE CONCLUSION / REMARKS
INHALATION:
TOXICITY (RAT): MINIMALLY TOXIC. BASED ON TEST DATA FOR
LC50: >5000 MG/M3 STRUCTURALLY SIMILAR MATERIALS.
IRRITATION: NEGLIGIBLE HAZARD AT AMBIENT/NORMAL
HANDLING
NO END POINT DATA. TEMPERATURES BASED ON ASSESSMENT OF THE
COMPONENTS
INGESTION:
TOXICITY (RAT): MINIMALLY TOXIC. BASED ON TEST DATA FOR
LD50: >2000 MG/KG STRUCTURALLY SIMILAR MATERIALS.
SKIN:
TOXICITY (RABBIT): MINIMALLY TOXIC. BASED ON TEST DATA FOR
LD50: >2000 MG/KG STRUCTURALLY SIMILAR MATERIALS.
IRRITATION (RABBIT): NEGLIGIBLE IRRITATION TO SKIN AT AMBIENT
DATA AVAILABLE TEMPERATURES. BASED ON TEST DATA FOR
STRUCTURALLY SIMILAR MATERIALS.
EYE:
IRRITATION (RABBIT): MAY CAUSE MILD, SHORT-LASTING DISCOMFORT TO
DATA AVAILABLE EYES BASED ON TEST DATA FOR STRUCTURALLY
SIMILAR MATERIALS.
CHRONIC/OTHER EFFECTS:
CONTAINS:
BASE OIL SEVERELY REFINED: NOT CARCINOGENIC IN ANIMAL STUDIES.
REPRESENTATIVE MATERIAL PASSES IP-346, MODIFIED AMES TEST, AND/OR OTHER
SCREENING TESTS. DERMAL AND INHALATION STUDIES SHOWED MINIMAL EFFECTS; LUNG
NON-SPECIFIC INFILTRATION OF IMMUNE CELLS, OIL DEPOSITION AND MINIMAL
GRANULOMA FORMATION. NOT SENSITIZING IN TEST ANIMALS.
ADDITIONAL INFORMATION IS AVAILABLE BY REQUEST.
THE FOLLOWING INGREDIENTS ARE CITED ON THE LISTS BELOW: NONE.
REGULATORY LISTS SEARCHED:
1 = NTP CARC
2 = NTP SUS
3 = IARC 1
4 = IARC 2A
5 = IARC 2B
6 = OSHA CARC
| SECTION 12 ECOLOGICAL INFORMATION | |
THE INFORMATION GIVEN IS BASED ON DATA AVAILABLE FOR THE MATERIAL, THE
COMPONENTS OF THE MATERIAL, AND SIMILAR MATERIALS.
ECOTOXICITY:
MATERIAL: NOT EXPECTED TO BE HARMFUL TO AQUATIC ORGANISMS.
MOBILITY:
BASE OIL COMPONENT:
LOW SOLUBILITY AND FLOATS AND IS EXPECTED TO MIGRATE FROM WATER TO THE LAND.
EXPECTED TO PARTITION TO SEDIMENT AND WASTEWATER SOLIDS.
PERSISTENCE AND DEGRADABILITY:
BIODEGRADATION:
BASE OIL COMPONENT: EXPECTED TO BE INHERENTLY BIODEGRADABLE
BIOACCUMULATION POTENTIAL:
BASE OIL COMPONENT:
HAS THE POTENTIAL TO BIOACCUMULATE, HOWEVER METABOLISM OR PHYSICAL
PROPERTIES MAY REDUCE THE BIOCONCENTRATION OR LIMIT BIOAVAILABILITY.
| SECTION 13 DISPOSAL CONSIDERATIONS | |
DISPOSAL RECOMMENDATIONS BASED ON MATERIAL AS SUPPLIED. DISPOSAL MUST BE IN
ACCORDANCE WITH CURRENT APPLICABLE LAWS AND REGULATIONS, AND MATERIAL
CHARACTERISTICS AT TIME OF DISPOSAL.
DISPOSAL RECOMMENDATIONS:
PRODUCT IS SUITABLE FOR BURNING IN AN ENCLOSED CONTROLLED BURNER FOR FUEL
VALUE OR DISPOSAL BY SUPERVISED INCINERATION AT VERY HIGH TEMPERATURES TO
PREVENT FORMATION OF UNDESIRABLE COMBUSTION PRODUCTS. PROTECT THE
ENVIRONMENT. DISPOSE OF USED OIL AT DESIGNATED SITES. MINIMIZE SKIN CONTACT.
DO NOT MIX USED OILS WITH SOLVENTS, BRAKE FLUIDS OR COOLANTS.
REGULATORY DISPOSAL INFORMATION:
RCRA INFORMATION:
THE UNUSED PRODUCT, IN OUR OPINION, IS NOT SPECIFICALLY LISTED BY THE EPA
AS A HAZARDOUS WASTE (40 CFR, PART 261D), NOR IS IT FORMULATED TO CONTAIN
MATERIALS WHICH ARE LISTED AS HAZARDOUS WASTES. IT DOES NOT EXHIBIT THE
HAZARDOUS CHARACTERISTICS OF IGNITABILITY, CORROSITIVITY OR REACTIVITY AND
IS NOT FORMULATED WITH CONTAMINANTS AS DETERMINED BY THE TOXICITY
CHARACTERISTIC LEACHING PROCEDURE (TCLP). HOWEVER, USED PRODUCT MAY BE
REGULATED.
EMPTY CONTAINER WARNING:
EMPTY CONTAINER WARNING (WHERE APPLICABLE):
EMPTY CONTAINERS MAY CONTAIN RESIDUE AND CAN BE DANGEROUS. DO NOT ATTEMPT
TO REFILL OR CLEAN CONTAINERS WITHOUT PROPER INSTRUCTIONS. EMPTY DRUMS
SHOULD BE COMPLETELY DRAINED AND SAFELY STORED UNTIL APPROPRIATELY
RECONDITIONED OR DISPOSED. EMPTY CONTAINERS SHOULD BE TAKEN FOR RECYCLING,
RECOVERY, OR DISPOSAL THROUGH SUITABLY QUALIFIED OR LICENSED CONTRACTOR AND
IN ACCORDANCE WITH GOVERNMENTAL REGULATIONS. DO NOT PRESSURISE, CUT, WELD,
BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME,
SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY EXPLODE
AND CAUSE INJURY OR DEATH.
| SECTION 14 TRANSPORT INFORMATION | |
LAND (DOT): NOT REGULATED FOR LAND TRANSPORT
LAND (TDG): NOT REGULATED FOR LAND TRANSPORT
SEA (IMDG): NOT REGULATED FOR SEA TRANSPORT ACCORDING TO IMDG-CODE
AIR (IATA): NOT REGULATED FOR AIR TRANSPORT
| SECTION 15 REGULATORY INFORMATION | |
OSHA HAZARD COMMUNICATION STANDARD:
WHEN USED FOR ITS INTENDED PURPOSES, THIS MATERIAL IS NOT CLASSIFIED AS
HAZARDOUS IN ACCORDANCE WITH OSHA 29 CFR 1910.1200.
COMPLIES WITH THE FOLLOWING NATIONAL/REGIONAL CHEMICAL INVENTORY
REQUIREMENTS: PICCS, KECI, TSCA, EINECS, DSL, AICS, IECSC
SPECIAL CASES:
INVENTORY STATUS
ENCS RESTRICTIONS APPLY
EPCRA: THIS MATERIAL CONTAINS NO EXTREMELY HAZARDOUS SUBSTANCES.
SARA (311/312) REPORTABLE HAZARD CATEGORIES: NONE
SARA (313) TOXIC RELEASE INVENTORY:
THIS MATERIAL CONTAINS NO CHEMICALS SUBJECT TO THE SUPPLIER NOTIFICATION
REQUIREMENTS OF THE SARA 313 TOXIC RELEASE PROGRAM.
THE FOLLOWING INGREDIENTS ARE CITED ON THE LISTS BELOW: NONE
REGULATORY LISTS SEARCHED:
1 = ACGIH ALL
2 = ACGIH A1
3 = ACGIH A2
4 = OSHA Z
5 = TSCA 4
6 = TSCA 5A2
7 = TSCA 5E
8 = TSCA 6
9 = TSCA 12B
10 = CA P65 CARC
11 = CA P65 REPRO
12 = CA RTK
13 = IL RTK
14 = LA RTK
15 = MI 293
16 = MN RTK
17 = NJ RTK
18 = PA RTK
19 = RI RTK
CODE KEY:
CARC=CARCINOGEN
REPRO=REPRODUCTIVE
| SECTION 16 OTHER INFORMATION | |
N/D = NOT DETERMINED
N/A = NOT APPLICABLE
THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:
REVISION CHANGES:
SECTION 09: PHYS/CHEM PROPERTIES NOTE WAS MODIFIED.
SECTION 09: FLASH POINT C(F) WAS MODIFIED.
SECTION 15: NATIONAL CHEMICAL INVENTORY LISTING WAS MODIFIED.
SECTION 08: EXPOSURE LIMITS/STANDARDS WAS MODIFIED.
THE INFORMATION AND RECOMMENDATIONS CONTAINED HEREIN ARE, TO THE BEST OF
EXXONMOBIL'S KNOWLEDGE AND BELIEF, ACCURATE AND RELIABLE AS OF THE DATE
ISSUED. YOU CAN CONTACT EXXONMOBIL TO INSURE THAT THIS DOCUMENT IS THE MOST
CURRENT AVAILABLE FROM EXXONMOBIL. THE INFORMATION AND RECOMMENDATIONS ARE
OFFERED FOR THE USER'S CONSIDERATION AND EXAMINATION. IT IS THE USER'S
RESPONSIBILITY TO SATISFY ITSELF THAT THE PRODUCT IS SUITABLE FOR THE
INTENDED USE. IF BUYER REPACKAGES THIS PRODUCT, IT IS THE USER'S
RESPONSIBILITY TO INSURE PROPER HEALTH, SAFETY AND OTHER NECESSARY
INFORMATION IS INCLUDED WITH AND/OR ON THE CONTAINER. APPROPRIATE WARNINGS
AND SAFE-HANDLING PROCEDURES SHOULD BE PROVIDED TO HANDLERS AND USERS.
ALTERATION OF THIS DOCUMENT IS STRICTLY PROHIBITED. EXCEPT TO THE EXTENT
REQUIRED BY LAW, RE-PUBLICATION OR RETRANSMISSION OF THIS DOCUMENT, IN
WHOLE OR IN PART, IS NOT PERMITTED. THE TERM, "EXXONMOBIL" IS USED FOR
CONVENIENCE, AND MAY INCLUDE ANY ONE OR MORE OF EXXONMOBIL CHEMICAL COMPANY,
EXXON MOBIL CORPORATION, OR ANY AFFILIATES IN WHICH THEY DIRECTLY OR
INDIRECTLY HOLD ANY INTEREST.
INTERNAL USE ONLY:
MHC: 0, 0, 0, 0, 0, 0
PPEC: A
DGN: 2008423XUS (1013559)
COPYRIGHT 2002 EXXON MOBIL CORPORATION, ALL RIGHTS RESERVED